安徽专业元素分析仪咨询报价

Procedure - Solid Samples

Prepare the instrument as outlined in the operator's instruction manual.

Determine the instrument blank.

Login a minimum of 3 Blank replicates.

Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open. Place a 502-344 Nickel Basket into the loading head.

Note: samples using automation should be placed in the appropriate autoloader position before starting the

analysis sequence. Once the sequence has started, the automatic analysis will start and end automatically.

氧氮氢分析仪选哪家？给您推荐上海禹重！安徽专业元素分析仪咨询报价

Instrument Highlights and Features

Features and Benefits

LED light ring illuminates the furnace area

Choice of either argon or helium carrier gas

Novel electrode design increases heat transfer efficiency for increased stability

Non-touch interface systems are also available

User-friendly brand software

High-Performance Detector Design

Thermostatic construction provides increased protection from ambient temperature fluctuations

Optimized emitter control and detection circuitryimproves the IR cell lifetime and long-term stability,

resulting in superior accuracy and precision

Infrared detection for the determination of oxygen, thermoconductivity detection for the determination

of nitrogen

山西专业元素分析仪多少钱高性能的红外检测器配置***恒温绝热技术，消除了外界环境温度的干扰。

氧氮氢分析仪的常见故障及解决方法

供电正常、通讯正常，点击确认键后分析仪不工作。这是没有水流，炉子温度太高或仪器通道电压不正常。如没有水流，炉子温度太高这些信息会显示在显示器画面上，但没有信息显示说明这两项正常。接下来检查仪器通道零位电压，如果比±3V高出1V以上，可能是因为气瓶空了，或者是空气进入到分析仪中。检查并更换化学试剂，如果有空气进入热导池里，热导池的电压就会＜-6V，此时打开右面的门，堵住炉子气体进口，10s后，热导池电压值必然升高。经过逐一排查，**终确认碱石棉有问题，更换后仪器正常。

Procedure – Powder/Chip Samples

Determine the instrument blank.

Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 2b through 2g a minimum of three times.

Set the blank following the procedure outlined in the operator's instruction manual.

Instrument calibration/drift correction.

Login a minimum of three Standard reps.

Weigh approximately *** grams of a calibration/drift standard into a *** Nickel Capsule; enter the mass and standard identification into appropriate rep fields. If applicable, place the nickel capsule in the appropriate autoloader position.

Note: LECO Reference Materia***o not require preparation. See preparation statement on the reference material certificate. Solid Standards may be used to calibrate when chip or powder standards are not available.

OHN836系列仪器采用惰性熔融法。

氧氮氢分析仪的常见故障及解决方法：

氧和氮空白值超过20。这是由于气流小，不能将炉子中的空气驱赶出去。可调节气体流量，调节载气压力在0.2~0.4MPa。接通仪器载气，放一个石墨坩埚在下电极上，打开主电源开关，点击软件上的关炉按钮，关闭炉子并等待10s。调节流量调节器，直到流量计a显示为30L／h，打开炉子。调节调节器直到流量计b显示为50L／h，再次关闭炉子。如果以上设置不稳定，则增加流量至100L／h，反复调节直至仪器稳定。 全自动分析系统（可选） 。新疆进口分析仪厂家直销

ONH836仪器通过***采纳客户的反馈意见和创新设计。安徽专业元素分析仪咨询报价

Instrument calibration/drift correction.

a. Login a minimum of 3 Standard replicates.

b. Weigh a ~1.000 gram of a calibration/drift standard, enter the mass and standard identification into appropriate replicate fields.

c. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

d. Place the calibration/drift standard into the open port at the top of the loading head.

e. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

安徽专业元素分析仪咨询报价

上海禹重实业有限公司致力于仪器仪表，以科技创新实现***管理的追求。禹重科技作为从事仪器科技、医疗科技、检测科技领域内的技术咨询、技术服务，仪器仪表的修理，仪器仪表、实验室设备、机械设备及配件、机电设备及配件、电子产品、化工产品及原料（除危险化学品、监控化学品、烟花爆竹、民用易爆物品、易制毒化学品）、第二类医疗器械的销售，机械设备租赁，电子商务，货物进出口，技术进出口。的企业之一，为客户提供良好的光谱仪，色谱仪，质谱仪，样品前处理。禹重科技不断开拓创新，追求出色，以技术为先导，以产品为平台，以应用为重点，以服务为保证，不断为客户创造更高价值，提供更优服务。禹重科技始终关注仪器仪表行业。满足市场需求，提高产品价值，是我们前行的力量。