山东元素分析仪厂家供应

氧氮氢分析仪

氧氮氢分析仪是一种用于材料科学领域的仪器，于2016年03月09日启用。

技术指标

测量范围： ON 低氧0.0－300ppm OH 低氧0.0－300ppm 高氧0.0－2% 高氧0.0－2% 低氮0.0―300ppm 低氢0.0－50ppm 高氮0.0－2% 高氢0.0－1000ppm 灵敏度： 氧0.01ppm；氮0.1ppm；氢0.01ppm。

主要功能

该仪器配置有16位微处理器和两个**的分别检测高氧和低氧的 红外检测池。氮和氢通过双重范围的热导检测池测量。分析过程中可自动实现从 低范围到高范围的切换。样品在高功率脉冲炉的石墨坩埚中加热可达3000℃以上 高温，脉冲炉采用循环水冷却。该仪器具有灵敏度高、性能好、测量范围宽和分 析结果准确可靠等优点。ONH-2000氧氮氢分析仪是为快速、准确测定铜、钢、铸 铁、合金、钛、镍、钼、锆、陶瓷和其它无机材料中氧、氮、氢的含量而专门设计 制造的。 力可**的动态流量补偿控制DFC系统，保证了流量系统的完善，可以精确控制整个气路中的流量。山东元素分析仪厂家供应

Summary

The determination of the amount of oxygen, nitrogen, and hydrogen in iron, steel, nickel-, and cobalt-base alloys represents some of the most important quality metrics for these materials. Oxygen is used to create steel from pig iron by removing excess carbon. Oxygen content must be controlled to limit the amount of carbon monoxide that can be formed during solidification which may cause excessive porosity. Nitrogen is considered both an impurity as well as an important alloying agent. Itcan be present as a nitride or interstitially in its gaseous form. Increased nitrogen content is known to increase yield and tensile strength, thus decreasing ductility and formability. Excessive levels may evolve during solidification thus increasing porosity. High hydrogen content is the primary cause of embrittlement, blistering and flaking due to its high

mobility through the lattice and provides no potential alloying benefits. The ONH836 utilizes a high-power

electrode furnace to quickly and efficiently release the target gases from within the sample, which allows

for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.

湖南专业元素分析仪优惠价格上海禹重给您提供各种氧氮氢分析仪，欢迎来电咨询！

仪器的亮点和优势：

特点和优势

·炉头区域LED照明系统

·炉头快速拆装的粉尘过滤装置

·装有自动旁路阀的可快速拆装氧水捕集装置

·**的动态流量补偿（DFC）保证热导池气体流量、压力恒定

高效脉冲炉冷却系统

·强力内循环水冷装置热交换效率

·双直流风扇保证持续冷却，不受电压波动的影响

·***电极炉头设计，提高脉冲炉

全自动分析系统（可选）

·自动清扫装置

·20位或100位全自动分析系统

·高效全自动真空除尘装置直接将粉尘排至仪器外部捕集器中，消除环境污染

改进的红外检测池技术

·***红外池的恒温绝热技术消除了外界环境温度的干扰

·长寿命的红外发射光源和无漂移的电路设计保证红外检测池的长期稳定性

·氧高低双量程采用3个碳红外检测器同时检测一氧化碳和二氧化碳，保证准确定量

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

One of the most critical chemical specifications of titanium alloys is the hydrogen content. Too high of a

hydrogen content can cause hydrides to precipitate, which can lead to embrittlement and subsequent

cracking when the alloy is stressed. Hydrogen pickup typically occurs during downstream processing steps

such as heat treating, pickling, and cleaning.

The LECO ONH836 is a simultaneous oxygen, nitrogen, and hydrogen determinator that utilizes an electrode furnace, inert carrier gas, and both infrared and thermal conductivity detection to meet the analytical needs of the refractory metal industry. 

This application note was written specifically for use with the LECO ONH836 series determinator.

Procedure - Solid Samples

Determine the instrument blank.

Repeat steps 2b through 2g a minimum of three times.

Set the blank following the procedure outlined in the operator's instruction manual.

Instrument calibration/drift correction.

Login a minimum of 3 Standard replicates.

Weigh approximately *** grams of a calibration/drift standard, enter the mass and standard identification into appropriate replicate fields.

Note: LECO Reference Materia***o not require preparation.See preparation statement on the reference material certificate.

试样加载过程中完全密闭，消除大气的中可能带来的杂质的污染。北京分析仪厂家直销

20位或100位全自动分析系统。山东元素分析仪厂家供应

Instrument calibration/drift correction.

a. Login a minimum of 3 Standard replicates.

b. Weigh a ~1.000 gram of a calibration/drift standard, enter the mass and standard identification into appropriate replicate fields.

c. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

d. Place the calibration/drift standard into the open port at the top of the loading head.

e. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

山东元素分析仪厂家供应

上海禹重实业有限公司致力于仪器仪表，是一家服务型的公司。公司业务分为光谱仪，色谱仪，质谱仪，样品前处理等，目前不断进行创新和服务改进，为客户提供良好的产品和服务。公司秉持诚信为本的经营理念，在仪器仪表深耕多年，以技术为先导，以自主产品为重点，发挥人才优势，打造仪器仪表良好品牌。禹重科技秉承“客户为尊、服务为荣、创意为先、技术为实”的经营理念，全力打造公司的重点竞争力。